Filament test report

All material was tested on the printer Weedo X40 without closure. The tests carried out were financed by donations from users. The ratings are independent and also subjective. Results may be different with other printers.

If you're new to 3D printing, then check out the Prusa Marerial Guide.
 
So far over 45 different filaments have been tested!
 
 
 
All 11 print profiles of the Cura X40 community configuration were tested. The rating was carried out on the basis of all 11 prints. If resealable packaging is not included, then I deducted one point, as correct storage is very important for print quality. See also Store filament correctly.
 
 

Filament selection 

If possible, filaments with a very precise diameter were selected (Toleranc +/-0,02mm ... +/-0,03mm). Together with an extruder calibration, over- or under-extrusion can thus be avoided.
Changing the filament during a print should also not be a problem when the filament sensor is active. Flow adjustment is not necessary for most of the filaments tested.
 
 
 Manufacturer: 3DJAKE
 Filament: ecoPLA
 Colour: All
 Part surface: Semi-gloss
 Description:

With a little fine tuning, useful results can be achieved. The material is characterized by an extremely large variety of colors.
No resealable packaging.

The rating has been upgraded because, in contrast to other PLA filaments, it still delivers acceptable printer results even after long storage.

 Stettings:

Nozzle 0,4mm
Problems with overhangs can occur with the Extra Fine print profile with a 0.4mm nozzle.

Printing results:

 

 

 Rating:  

 

 
 Manufacturer: 3DJAKE
 Filament: ecoPLA Matt
 Colour: All
 Part surface: Matt
 Description:

Excellent prints can be created with the filament without much difficulty.
No resealable packaging.

There is a point deduction due to the lack of resealable packaging.

 Stettings:

Nozzle 0,4mm

Printing results:

 

 

 Rating:  

 

 
 Manufacturer: 3DJAKE
 Filament: ecoPLA Silk
 Colour: All
 Part surface: Semi-gloss
 Description:

Excellent prints can be created with the filament without much difficulty.
No resealable packaging.

There is a point deduction due to the lack of resealable packaging.

 Stettings:

Nozzle 0,4mm

Printing results:

 

 

 Rating:  

 

 

 Manufacturer: 3DJAKE
 Filament: ecoPLA Tough
 Colour: All
 Part surface: Semi-gloss
 Description:

The material is easy to print and has high strength. Due to the high level of layer adhesion, the printed object is difficult to detach from a raft, so if possible no raft should be used.
No resealable packaging.

There is a point deduction due to the lack of resealable packaging.

 Stettings:

Nozzle 0,4mm

Printing results:

 

 

 Rating:  

 

 
 Manufacturer: 3DJAKE
 Filament: PETG
 Colour: All
 Part surface: Semi-gloss
 Description: The material can be easily processed like normal PETG. There are no particular abnormalities. The filament is not supplied with a resealable packaging, so one point is deducted.
 Stettings:

Nozzle 0,4mm
Problems with overhangs can occur with the Extra Fine print profile with a 0.4mm nozzle.

Printing results:

 

 

 Rating:  

 

 

 
 Manufacturer: AddNorth
 Filament: E-PLA
 Colour: All
 Part surface: Matt
 Description: The E-PLA filament from AddNorth has convinced across the board and is very likely one of the best PLA materials on the market. The material is easy to work with, shows no stringing and cleanly reproduces the contours of the model. With resealable packaging, it is worth recommending.

AddNorth E-PLA is our printer calibration reference material. With a flow of 100%, the exact dimensions come out with only minor deviations. For all other materials, the flow may have been adjusted.
 Stettings:

Nozzle 0,4mm

Printing results:

 

 

 Rating:

 X40-Community Referenz Material

 

 
 
 Manufacturer: AddNorth
 Filament: X-PLA
 Colour: All
 Part surface: Matt
 Description: The AddNorth X-PLA is not as easy to print as the E-PLA. Wrong parameters result in unclean edges. With the X40 community print profiles, this is not a problem. With the white material, the layers are clearly visible.
A resealable packaging is included.
 Stettings:

Nozzle 0,4mm

Printing results:

 

 

 Rating:  

 


 
 Manufacturer: AddNorth
 Filament: PLA-Wood
 Colour: All
 Part surface: Matt
 Description: AddNorth PLA-Wood is one of the few wood filaments that can be printed with a 0.4mm nozzle without clogging. In addition, the material does not create stringing. For me one of the best wood filaments on the market. A resealable packaging is included. 
The wood filament from Fiberlogy, however, feels much more like wood and also looks a lot more like wood.
 Stettings:

Nozzle 0,4mm

Printing results:

 

 

 Rating:  

 

 

 
 Manufacturer: AddNorth
 Filament: PETG
 Colour: All
 Part surface: Matt
 Description: As usual with PETG, the material is easy to print. However, support structures may warp. A resealable packaging is included. 
 Stettings:

Nozzle 0,4mm

Printing results:

 

 

 Rating:  

 


 
 Manufacturer: AddNorth
 Filament: Textura Flare
 Colour: All
 Part surface: Matt
 Description: Textura Flare is a wonderful material. The material is not only very easy to print, but also hides the layers thanks to its special composition. Straight sidewalls look like they were made of one piece without showing that it was created with an FDM printer.
A resealable packaging is included.
 
 Stettings:

Nozzle 0,4mm

Printing results:

 

 

 Rating:  

 

 

 
 Manufacturer: AddNorth
 Filament: Adura™ (Nylon, Polyamid)
 Colour: All
 Part surface: Shiny
 Description:

AddNorth Adura is a nylon filament with the typical nylon properties such as high toughness and strength, good chemical resistance. In addition to the good properties, there are also some that cause problems such as warping, shrinkage and moisture absorption. Adura is more difficult to work with and therefore somewhat inconvenient for experienced users. The biggest problem is poor bed adhesion and warping. It works best with adhesion promoter or PEI printing bed. Adura adhere very well to the P-surface 141 printing surface without an additional adhesion promoter.

The filament absorbs moisture very quickly. Make sure you store it properly or dry it before use, otherwise you will get strining etc. Due to the shrinkage, dimensionally stable parts are very difficult to achieve.


Note:
The P-surface 141 bed surface works differently than the usual ones. Printing is done on a non-heated print bed. To detach the print object, the heating bed must be heated to 80°C and the print object carefully removed.

 Stettings:

Nozzle 0,4mm

Printing results:

 

 

 Rating:  

 

 

 
 Manufacturer: AddNorth
 Filament: OBC Polyethylene
 Colour: All
 Part surface: Matt
 Description:

OBC Polyethylene is the most difficult material to print with PP and therefore only suitable for experts. Even with an adhesion promoter, the material does not stick to any of the usual surfaces. The P-surface 141 printing surface is required for printing, and you also need a 0.6mm nozzle, since the material is very soft, similar to TPU, and otherwise the material transport does not work reliably.
OBC Polyethylene is a flexible but not compressible material like TPU.
It is therefore suitable for printing components with a clip function or a film hinge.
 

Note:
The P-surface 141 bed surface works differently than the usual ones.
Printing is done on a non-heated print bed. To detach the print object, the heating bed must be heated to 80°C and the print object carefully removed.

 Stettings:

Nozzle 0.6mm (Nozzle 0.4mm doesn't work!)

Printing results:

 

 

 Rating:  

 

 
 

 
 Manufacturer: ColorFabb
 Filament: ALLPHA
 Colour: All
 Part surface: Mat ... semi-gloss
 Description:

With regard to environmental protection, ALLPHA is definitely not the right first step, but the quality of the prints cannot yet keep up with the usual PLA materials. While there is absolutely no stringing and the fact that PHA absorbs almost no water has its advantages, the edges and dimensions are not that good. I think it's useful for figures or a quick print for a first draft. Here you don't have to worry about unnecessarily polluting the environment with a misprint. 
The Layher adhesion is very good, so you can put loads on the parts.

Because of the good world compatibility, there is an extra bonus in the rating.

See the full review

 Stettings:

Nozzle 0.4mm, I recommend using Dimafix against warping.

Printing results:

 

 Rating:  

 

 

 
 Manufacturer: ColorFabb
 Filament: PLA/PHA
 Colour: All
 Part surface: Mat ... semi-gloss
 Description:

The ColorFabb PLA/PHA filament could become one of my new favorite materials. Due to the PHA content, it has significantly better layer adhesion than normal PLA. The material is very well suited for high-speed printing up to 100mm/s. With very slow printing of 30mm/s, the print quality even decreases.

Unfortunately without resealable packaging, otherwise it would have received full marks.

 Stettings:

Nozzle 0.4mm

Printing results:

 

 Rating:

The material tip!

 

 
 Manufacturer: ColorFabb
 Filament: NGEN
 Colour: All
 Part surface: Mat ... semi-gloss
 Description:

The ColorFabb NGEN produces a clean print image. Overhangs in particular can be printed very well with the material. Even overhangs over 45° can be printed with a layer height of 0.24mm. If the cooling is too high, the material becomes brittle and fragile. If the cooling is too low, chatter marks will quickly appear. I couldn't manage a clean separation from a raft.

Unfortunately without resealable packaging, otherwise it would have received full marks.

 Stettings:

Nozzle 0.4mm

Printing results:

 

 Rating:

 

 
 
 Manufacturer: Extrudur
 Filament: GreenTEC
 Colour: All
 Part surface: Mat ... semi-gloss
 Description: GreenTEC is the predecessor material of GreenTEC Pro. The characteristics are similar. The biggest difference is the lower heat resistance of at least 115°C. The material can be processed just like PLA. A resealable packaging is unfortunately not included, so one point is deducted. 
 Stettings: Nozzle 0,4mm
 Printing results:

 

 Rating:

 

 

 
 
 Manufacturer: Extrudur
 Filament: GreenTEC Pro
 Colour: All
 Part surface: Mat ... semi-gloss
 Description: The material is easy to process like PLA and has a pleasant feel. The special thing about the filament is its extremely high heat resistance. Despite the high price, it gets five benchy's from us. No resealable packaging is included, hence a point deduction. Since GreenTec Pro has the highest material compatibility, there is an extra point that leads to test victory. 
 Stettings: Nozzle 0,4mm
Problems with overhangs can occur with the Extra Fine print profile with a 0.4mm nozzle.
 Printing results:

 

 

 Rating:

 The material test winner 

 

 
 
 Manufacturer: Extrudur
 Filament: BioFusion
 Colour: All
 Part surface: Shiny metallic
 Description:  The material is very difficult to print. If the cooling is too much, the layers will not adhere. If there is too little cooling, the component deforms in e.g. the chimney of the Benchy. I didn't get any useful results with the original Weedo X40 component fan.
Useful results can only be achieved with the X40 community cooling system.
The material can only be used for demonstration objects. In the case of components with a load, it breaks. In addition, the bed adhesion is very poor.
 Stettings:

Nozzle 0,4mm
Problems with overhangs can occur with the Extra Fine print profile with a 0.4mm nozzle.

Because of the big problem, the print profiles have not yet been published!

 Printing results:

 

 

 Rating:  

 

 

 
 Manufacturer: Extrudur
 Filament: FlexMedium
 Colour: All
 Part surface: Shiny
 Description: FelxMedium is an elastic TPU with 98 Shore A. The material is stiff enough to be printed with the Weedo X40. Setting the right parameters is a little tricky. The printing temperature and part cooling must be perfectly coordinated. In the photos, the surface looks worse than it is.
 Stettings:

Nozzle 0,4mm

 Printing results:

 Rating:  

 

 

 
 Manufacturer: Extrudur
 Filament: PETG
 Colour:  GlowEX
 Part surface:  Semi-gloss
 Description: The Weedo X40 only manages to transport the material from a nozzle size of 0.6mm. Although the material was only removed from the unopened, new vacuum packaging shortly before printing, the material shows clear stringing. The support structure in the inner area is only no longer visible from a wall thickness of 3 layers. Except for the stringing, the Benchy are printed without any major problems. If you expose the GlowEX material to a strong light source for a long time and then go into the dark, the material glows. The glow does not last very long, however. Set up the objects outside and see them glow at night, unfortunately, does not work because the object does not glow long enough! 
 Stettings:

Nozzle 0,6mm

 Printing results:

 

 Rating:  

 

 

 
 
 Manufacturer: Fiberlogy
 Filament: Easy PLA
 Colour: All
 Part surface: Mat ... semi-gloss
 Description: When you hear the name Easy PLA, you first think that it is easy to work with. The tests quickly showed that the 0.4mm nozzle clogged quickly and the material did not transport (tested with Weedo X40 and Creality Ender 3 Pro). If you use the 0.6mm or larger you can get great results with the material.
Since it cannot be processed as easily as normal PLA materials and the Weedo X40 only works really well with a 0.6mm nozzle, there are only three benchy's.
Resealable packaging is included.
 Stettings: Nozzle 0,6mm. The 0,4mm nozzle is clogged or the material is not feeding properly.
 Printing results:

 

 

 Rating:  

 

 

 
 
 Manufacturer: Fiberlogy
 Filament: FiberSilk
 Colour: All
 Part surface: Shiny metallic
 Description: The material swells as it cools. The lower the cooling capacity, the greater the swelling. An elephant's foot is therefore inevitable. The material requires a very good cooling capacity, so it is essential to use the X40 community cooling system.
The shiny metallic surface can cause a change in the degree of gloss in some geometries. With small radii, for example on the back of the Benchy or the bow tip, rough surfaces can arise.
The material is unsuitable for very small layers.
The adhesion of the layers and the bed is very good.
A flow below 100% is required for good surfaces, otherwise pimples will develop.
 Stettings: Nozzle 0,4mm, Unsuitable with print profile extra fine (0,12 Layer height)
 Printing results:

 

 Rating:

 

 

 
 
 Manufacturer: Fiberlogy
 Filament: FiberSatin
 Colour: All
 Part surface: Mat
 Description: After the name FiberSatin, one would think the component would look like satin. For me it came out matt. Since I had test material, I could not do any further tests, hence no evaluation.
 Stettings: Nozzle 0,4mm
 Printing results:

 

 Rating:

 

 

 
 Manufacturer: Fiberlogy
 Filament: Impact PLA
 Colour: All
 Part surface: Mat ... semi-gloss
 Description: The material was a big surprise. Not only is the layer and bed adhesion very good, we can also confirm the advertised high strength and rigidity.
We are now using this material as a standard construction material. In addition to its great properties, it can be easily processed and is not much more expensive than normal PLA.
With resealable packaging, our material tip!
 Stettings: Nozzle 0,4mm
Problems with overhangs can occur with the Extra Fine print profile with a 0.4mm nozzle.
 Printing results:

 

 

 Rating:  

The material tip!

 

 

 
 
 Manufacturer: Fiberlogy
 Filament: Fiberwood
 Colour: All
 Part surface: Mat
 Description: The material with the addition of wood produces strong stringing regardless of the retraction settings. Drying the filament didn't help either. Most parts cannot be used without rework.
The wood smell when printing may be great at the beginning, but after a while it gets really annoying.
The material didn't really convince me.
Resealable packaging was not available, although all other Fiberlogy filaments have one.
 Stettings:  Nozzle 0,6mm. A 0,4mm nozzle clogged 
 Printing results:

 

 

 Rating:  

 

 

 
 
 Manufacturer: Fiberlogy
 Filament: Easy PET-G
 Colour: All
 Part surface: Semi-gloss ... glossy
 Description: The name says it all again. The material is easy to work with and does not show any clear weaknesses. The feel is reminiscent of a PET bottle.
Resealable packaging is available.
A raft can not be removed easily or not at all with the material. I haven't found a perfect air gap value.
 Stettings:  0,4mm Nozzle
 Printing results:

 

 

 Rating:  

 

 

 
 
 Manufacturer: Fiberlogy
 Filament: PCTG
 Colour: All
 Part surface: Mat ... semi-gloss
 Description: The material is easy to process and the layer adhesion is very good.
 Stettings: Nozzle 0,4mm
The material transport with the Weedo X40 Extruder is borderline. Since the temperatures are already at the end of the Weedo X40, only printing more slowly or using a 0.6mm nozzle helps in the event of problems.
 Printing results:  
 Rating:  

 

 

 
 
 Manufacturer: Fiberlogy
 Filament: PLA Mineral
 Colour: All
 Part surface: Mat
 Description: This PLA material was a real surprise. Stringing is apparently excluded by the minerals in the PLA. In addition to very detailed models, the material also impressed when printing overhangs.
With resealable packaging you get full marks. it doesn't get any better than that.
 Stettings:

0,4mm Nozzle
Also convincing when printing overhangs with a layer height of only 0.12mm.

 Printing results:

 

 

 Rating:  

 

 

 
 
 Manufacturer: Fiberlogy
 Filament: ASA
 Colour: All
 Part surface: The surface is completely matt
 Description: The material can be printed at 260°C without warping. An adhesion promoter such as Dimafix is necessary so that the material adheres to the print bed of the Weedo X40. For small components you also need a raft, as the adhesion promoter is not sufficient. The material can be used to manufacture precise and stable components. When printing the Benchy, the material always created a small visible step under the beltline. The cause is not known, therefore no point deduction. The material is delivered with resealable packaging.
 Stettings:  Nozzle 0,4mm; Printed with Dimafix and raft support
 Printing results:  
 Rating:  

 

 

 
 
 Manufacturer: Fiberlogy
 Filament: PP
 Colour: All
 Part surface: The surface is completely matt
 Description: PP is extremely difficult to print. The material does not adhere to the overlying print bed. By using Magigoo for PP you get the material to adhere to the print bed. The second difficulty is the flexibility of the filament. The filament is similarly soft as TPU and blocks extremely quickly with a Bowden cable system. The great thing about the material is the extreme layer adhesion and toughness. The layer adhesion is so good that you cannot remove a support structure or a raft made from the same material. The layers are barely visible. The material can only be processed to a very limited extent with a Bowden cable system. There are therefore no print profiles for the Weedo X40. 
 Stettings: Nozzle 0,4mm; Printed with Magigoo for PP and raft support
 Printing results:  
 Rating:  

 

 

 
 
 Manufacturer: Fiberlogy
 Filament: HIPS
 Colour: All
 Part surface: The surface is completely matt
 Description: HIPS is the only material that can be used for a printed object and as a support material for other materials. However, the solvent is not exactly environmentally friendly, so it should not be used as a support material if possible. When printing HIPS, the typical, unpleasant smell of polystyrene is immediately noticeable. The processing difficulty is comparable to PETG. 
 Stettings: Nozzle 0,4mm
 Printing results:  
 Rating:  

 

 

 
 
 Manufacturer: Fillamentum
 Filament: NonOilen
 Colour: All
 Part surface: Semi-gloss
 Description: NonOilen is a very special material. In contrast to PLA, this material can be composted without an industrial plant and does not form microplastics when it decomposes.
In addition, the material is temperature-stable up to over 100 ° C and can very often be recycled. The material has a nice feel. 
Processing is as easy as PLA.
Since the price is high and there is only one color, I had to subtract one point, hence only four benchys.
The raft and support can be easily removed and the surfaces are also nice and smooth.
 Stettings:  0,4mm Nozzle
 Printing results:

 

 

 Rating:  

 

 

 
 
 Manufacturer: Igus
 Filament: I150-PF
 Colour: White
 Part surface: Matt
 Description: Igus I150-PF is a wear-optimized plastic. It was designed so that a metal slides on the plastic. If both sliding partners are printed on the I150-PF (see picture), a slipstick effect can occur. An adhesion promoter is recommended for processing as the material tends to warp.
 Stettings:  0,4mm Nozzle; Printed with Dimafix and brim
 Printing results:

 

 

 Rating: No rating as only one sample was printed

 

 

 
 
 Manufacturer: Material4Print
 Filament: PLA
 Colour: All
 Part surface: Semi-gloss ... glossy
 Description: The material is well processed. It only shows slight weaknesses when printing overhangs with a layer height of 0.12mm.
Unfortunately, there is no resealable packaging
 Stettings:  0,4mm Nozzle
 Printing results:

 

 

 Rating:  

 

 

 
 
 Manufacturer: Material4Print
 Filament: PET-G
 Colour: All
 Part surface: High-glossy (like a new car)
 Description: The material is well processed. It only shows slight weaknesses when printing overhangs with a layer height of 0.12mm.
Unfortunately, there is no resealable packaging
 Stettings:  0,4mm Nozzle
 Printing results:

 

 

 Rating:  

 

 

 
 
 Manufacturer: Material4Print
 Filament: PMMA
 Colour: All
 Part surface: Matt
 Description: The PMMA material actually needs a printing bed with 100 °C. On the Weedo X40, however, it can also be used to a limited extent on the 80 °C bed with adhesion promoter. Warping can occur with large components; breakeaway support structure does not work well. If there is a small gap between the object and the support structure, the support structure cannot be removed cleanly. A larger gap results in warping. The material has absolutely no stringing. The filament is delivered without resealable packaging, hence a point deduction.
 Stettings:  0,4mm Nozzle; Printed with Dimafix and brim
 Printing results:

 

 Rating:  

 

 
 
 Manufacturer: Material4Print
 Filament: ASA
 Colour: All
 Part surface:  
 Description:  
 Stettings:  0,4mm Nozzle
 Printing results:

 

 Rating:  

 

 

 
 Manufacturer: Polymaker
 Filament: PolyTerra PLA
 Colour: All
 Part surface: The surface is completely matt
 Description: The material is easy to process. The layers can hardly be seen due to the dull matt surface. The packaging is resealable. 
 Stettings:  0,4mm Nozzle
 Printing results:

 

 Rating:  

 

 

 
 
 Manufacturer: Polymaker
 Filament: PolyMax PLA
 Colour: All
 Part surface: Semi-gloss 
 Description: The material is a little more difficult to work with. To get a perfect result you have to make a few test prints. Although the Benchy is symmetrical and also stood in the middle of the fan, the surfaces on the sides of the fuselage were slightly different. Whether one got better results with a higher printing speed than with a slow one. The packaging is resealable. Points deducted because of price performance and printability. 
 Stettings:  0,4mm Nozzle
 Printing results:  
 Rating:  

 

 

 
 
 Manufacturer: Polymaker
 Filament: PolyFlex TPU95
 Colour: All
 Part surface: Semi-gloss
 Description:  
 Stettings:  0,4mm Nozzle
 Printing results:
 Rating:  

 

 

 

 
 
 Manufacturer: Polymaker
 Filament: PolyLite PLA
 Colour: All
 Part surface: matt
 Description: The Polymaker PolyLite PLA filament is easy to process and you can get a good print with it. However, the print quality is not perfect, there are PLA filaments that produce a better print.
The filament comes in a resealable package.
 Stettings:  0,4mm Nozzle
 Printing results:
 Rating:  

 

 

 

 
 
 Manufacturer: Polymaker
 Filament: PolyLite PETG
 Colour: All
 Part surface: Semi-gloss
 Description: Unfortunately, the Polymaker PolyLite PETG disappointed me. Getting a clean print is difficult. With a lot of cooling, the print will be cleaner, but the component will be fragile and with little cooling, the print will be dirty. Drying the new filament didn't show any improvement either. Other PETG filaments can do this better. Of course, it can also be due to the crystal-clear material. The filament comes in a resealable package.
 Stettings:  0,4mm Nozzle
 Printing results:
 Rating:  

 

 

 
 
 
 
 Manufacturer: Prusament
 Filament: PVB
 Colour: All
 Part surface: Matt without aftertreatment, high-gloss finish with ethanol aftertreatment
 Description:

The special thing about the material is that you can smooth the surface with isopropanol. Regardless of the retraction settings, the material generates stringing when printing. The threads can be easily removed by mechanical removal and subsequent treatment with isopropanol.

The viscosity of the melt is so high that the Weedo X40 does not transport the filament with a 0.4mm nozzle. A 0.6mm nozzle must therefore be used.


Processing similar to PLA. Good transparency can be created for thin-walled parts with 100% filling and post-treatment.

The resealable packaging provided is important because the material absorbs moisture quickly.
Slight devaluation due to the high price and the stringing, hence only four benchy's.

 Stettings:  0,6mm Nozzle, A 0,4mm Nozzle doesn't work with the Weedo X40
 Printing results:

 

The contamination comes from contaminated isopropanol in the aftertreatment!

 Rating:  

 

 

  
 
 Manufacturer: Verbatim
 Filament: PLA
 Colour: All
 Part surface: Mat ... semi-gloss
 Description:

Verbatim filament is excellent and easy to process. The only negative point is that no resealable packaging is included.

After a long storage in the basement, miserable print quality. The dry spell didn't bring any significant improvement either. Strong stringing occurs and the layers no longer adhere well.

The rating has been devalued because it becomes unusable if stored for a long time. Even after drying, the layers no longer adhere properly.

 Stettings:  0,4mm Nozzle
 Printing results:

 

 

 Rating:  

 

 

 
 
 Manufacturer: Verbatim
 Filament: PET-G
 Colour: All
 Part surface: Semi-gloss ... glossy
 Description:

Verbatim filament is excellent and easy to process. The only negative points are that very light stringing can occur and that no resealable packaging is included

 Stettings:  0,4mm Nozzle
 Printing results:

 

 

 Rating:  

 

 

 
 
 
 Manufacturer: Verbatim
 Filament: DuraBio
 Colour: All
 Part surface: Glossy
 Description:

With DuraBio you can get a very clean and error-free printout. The material does not warp. The material actually requires a heating bed with 100 ° C, so that a good bed adhesion is achieved. Since the Weedo X40 can heat the heating bed to a maximum of 80 ° C, you have to use an adhesion promoter such as Dimafix and, for small parts, a raft. The raft is difficult to remove, however. Post-processing is often necessary.
No resealable packaging is included.

 Stettings:   0,4mm Nozzle
 Printing results:  
 Rating:  
 
 
 
 
 
 
 Manufacturer: FormFutura
 Filament: ApolloX ASA
 Colour: All
 Part surface: Mat ... semi-gloss
 Description:

The AppoloX from FormFutura is easy to print, but shows weaknesses with overhangs. The nose tip of the Benchy is not neatly worked out in almost all profiles. The first layer also often seems unclean. Although the manufacturer recommends an enclosed print, no warping occurred with the open Weedo X40. Resealable packaging is not included. There is a point deduction for poor nose tip and packaging.

 Stettings:  Nozzle 0,4mm; Printed with Dimafix and raft support
 Printing results:  
 Rating:  

 

 

 
 Manufacturer: Tarfuse
 Filament: ENVI 1
 Colour: Natural
 Part surface: Matt
 Description:

When freshly unpacked, the material delivers an excellent print image without stringing. However, the material absorbs water very quickly and then creates stringing (see picture). The material should be printed from a dry box like BVOH and should be dried before printing if necessary. A resealable packaging is included and the filament decomposes quickly without microplastics.

The material is intended for architectural models and figures to be painted. Material is not suitable for outdoor use!

Read the full report

 Stettings:  Nozzle 0,4mm
 Printing results:  
 Rating:  

 

 

 

 

 

 

 

 

 

 

 

 

Joomla templates by a4joomla